Notices
 

Thread: Honda CBR Shims

Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. Honda CBR Shims 
    #1
    Platinum Member
    Join Date
    Jun 2008
    Posts
    1,732
    Without sounding non technicaly inclined what are Shims? I have a slight tapping sound from the engine on my CBR600F4, 18K miles on the clock. I'm sure I've heard something about engines need top end setting every so often! Thanks!
     
     

  2. Re: Honda CBR Shims 
    #2
    Active Member
    Join Date
    May 2007
    Posts
    50
    without being too technical,i am no mechanic the shim sits on the end of the valve & under the valve lifter on the camshaft end.
    when the valve clearance has exceeded range then they need replacing....

    As you need to measure the gap then order shims which then maybe the wrong size best left to the pro,s who should have various sizes in stock.
    Yes this will be a light rattle especially when cold coming from the top end
    This is what i am led to believe i may stand corrected
     
     

  3. Re: Honda CBR Shims 
    #3
    Senior Member alanTDM's Avatar
    Join Date
    Dec 2006
    Posts
    600
    Theres a possibility that it could be your camchain tensioner which is causing chain to rattle slightly not sure how yours works on your bike but that might go as the tensioner moves inwards on its ratchet (if its got a ratchet system)
    Shims usally need doing every 25-30k miles cause they dont wear out so fast as adjustable manual(lock nut and screw) do which usally are every 4k.
    As the shims wear then the gap gets narrower so infact it tightens up which in extreme cases if left to long you end up with burnt valves cause they are not sealing properly.
    But phone up dealer to find out what mileage the shims have to be checked/replaced
     
     

  4. Re: Honda CBR Shims 
    #4
    Platinum Member
    Join Date
    Jun 2008
    Posts
    1,732
    Alan, thanks for that info mate. Never thought about the cam tensioner as a possibility. Sometimes the noise is louder then quietens other times. Im no expert. :-/
     
     

  5. Re: Honda CBR Shims 
    #5
    Active Member
    Join Date
    Mar 2008
    Posts
    483
    Quote Originally Posted by alanTDM
    As the shims wear then the gap gets narrower so infact it tightens up which in extreme cases if left to long you end up with burnt valves cause they are not sealing properly.
    I keep thinking about this statement since I read it last night and I'm struggling to understand it. If the shims sit on top of buckets which sit on top of the valves and are directly under the cam shaft as they would be in any OHC engine... then as they wear the gap between the cam and the shim is going to get wider/bigger.

    What am I missing?

    Thanks,
     
     

  6. Re: Honda CBR Shims 
    #6
    Senior Member alanTDM's Avatar
    Join Date
    Dec 2006
    Posts
    600
    Quote Originally Posted by hotdog
    [quote author=alanTDM link=1214322222/0#2 date=1216681922]As the shims wear then the gap gets narrower so infact it tightens up which in extreme cases if left to long you end up with burnt valves cause they are not sealing properly.
    I keep thinking about this statement since I read it last night and I'm struggling to understand it. If the shims sit on top of buckets which sit on top of the valves and are directly under the cam shaft as they would be in any OHC engine... then as they wear the gap between the cam and the shim is going to get wider/bigger.

    What am I missing?

    Thanks,[/quote]
    Your right about that i miss read the second post that would be the case they would widen, if the shims were underneath the buckets then it would tighten up I dont know how long he has had the bike but at 18k i would not of thought they would need doing yet for at least another 10k usually there checked at say a first service and if they have to have new shims not all but some its done then till the next major service eg 28k then every 28k depending on manufacture.If he has got to take it to a dealer to be done every 28k or whatever it will cost a lot in labour(fairing and watercoolant taken out etc) I done my own and the Yammy ones are about £2.50 each so not sure about Honda ones.The cost of dealer doing my TDM was £140 but have known peeps to pay £200 for shims to be replaced its the labour charges that hit your pocket.
    If the camchain is on the outer side of engine and not in the middle he could use a big screwdriver to listen to it to see if it is rattling by placing next to ear and other end on casing so it acts as a stethoscope
    But it just still could be the tensioner/camchain


     
     

  7. Re: Honda CBR Shims 
    #7
    Platinum Member
    Join Date
    Jun 2008
    Posts
    1,732
    You lads have lost me with this tech talk!lol . I'm down sallys' Thursday so if you're around have a listen to my bike and see what you think! Like I said before I'm not an expert on bike engines yet so apreciate comments given so far.
     
     

  8. Re: Honda CBR Shims 
    #8
    Senior Member alanTDM's Avatar
    Join Date
    Dec 2006
    Posts
    600
    Quote Originally Posted by Iceman
    You lads have lost me with this tech talk!lol . I'm down sallys' Thursday so if you're around have a listen to my bike and see what you think! Like I said before I'm not an expert on bike engines yet so apreciate comments given so far.
    I cant make this thursday
     
     

  9. Re: Honda CBR Shims 
    #9
    Platinum Member
    Join Date
    Jun 2008
    Posts
    1,732
    No worries Alan.thanks anyway!
     
     

  10. Re: Honda CBR Shims 
    #10
    Active Member
    Join Date
    Sep 2007
    Posts
    154
    I don't think it is possible just by listening to an engine wether the shims need doing. You may notice if the tensioner is worn, but I dont really know what to listen for. I did listen to your bike the last time I was at the Sally, and to be honest I thought it was perfectly fine.

    My CBR's shims are where due at 16000 miles and were done on the last service. 5 out of the 16 where changed cos the gap had changed. It was still runing great before it went in, but it was better once I picked it up. If you want peace of mind, like I did then get them done. It has been known for valves to burn out as has been said, but thats in extreme cases. Just don't do what I did, and that is spend a fortune on a service and a few other bits, then buy another bike
     
     

Posting Permissions
  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •