Notices
 

Search:

Type: Posts; User: alanTDM

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thread: Yamaha MT-07

    by alanTDM
    Replies
    3
    Views
    1,689

    Thats the same 270 crank engine as in the 2000...

    Thats the same 270 crank engine as in the 2000 TDM 850,The TDM 900 270 crank had fuel injection/ceramic bores and that does about 60mpg.So that bike with the same 270 cranked engine with only 700...
  2. Serious Bike Accident on A4 between Batheaston and Box.

    Serious bike accident between Box and Batheaston just after Z bend,happened about 4.15pm.Rider was airlifted to hospital but bike was burnt out on impact.I dont think any other cars etc were...
  3. Thread: Poor MPG

    by alanTDM
    Replies
    16
    Views
    5,074

    When did you last have the carbs balanced ?

    When did you last have the carbs balanced ?
  4. Thread: Poor MPG

    by alanTDM
    Replies
    16
    Views
    5,074

    When was the last time you had your carbs...

    When was the last time you had your carbs balanced?
  5. Replies
    18
    Views
    7,456

    Ooops missed your post about checking relay,if...

    Ooops missed your post about checking relay,if your lucky you might have a separate fuel pump relay,some Yamaha's have it combined with the Starter Circuit Cut off Relay with the F/Pump relay...
  6. Replies
    18
    Views
    7,456

    I think you have a Fuel pump relay on that bike...

    I think you have a Fuel pump relay on that bike check that, if that's Kaput no power to the pump
  7. Mark i will be going but straight to the...

    Mark i will be going but straight to the crematorium hoping to get there about 12.45 ,cant make it for 12.00 midday due to work.
  8. Used Carol Nash once 8 years ago that was enough...

    Used Carol Nash once 8 years ago that was enough never again:mad:
  9. Replies
    6
    Views
    5,984

    I got a solar charger for the car as i only use...

    I got a solar charger for the car as i only use the car about once a month but use the bike everyday,i had problems with battery not holding charge even though i was using it ,then the bike wouldn't...
  10. Replies
    5
    Views
    2,963

    This is bad news known him for years i sold him...

    This is bad news known him for years i sold him my XL185 years ago,Thats two mechanics that use to work at Bob Missens that have died in the last couple of months not good, Greg was the other.
    RIP...
  11. I would check if the float height is correct...

    I would check if the float height is correct aswell before changing jets if thats out it could give you a rich or lean mixture.
  12. Replies
    7
    Views
    2,690

    Been told that Infinity MC near Yate make custom...

    Been told that Infinity MC near Yate make custom Pipes so going to ring them and suss out the options.
  13. Thread: Forgetfulness

    by alanTDM
    Replies
    17
    Views
    6,935

    I went to work one morning and about a mile down...

    I went to work one morning and about a mile down the road noticed i wasnt wearing my glasses then everything went blurry lol had to go back and get them slowly
  14. Replies
    7
    Views
    2,690

    Hack saw wont touch it to tough,Anyway as i was...

    Hack saw wont touch it to tough,Anyway as i was coming back from Cornwall Sunday at *mph it decided to put a big hole in it just as i was overtaking a car didnt find out how loud(good) it was till i...
  15. Replies
    7
    Views
    2,690

    I was thinking more on the like of a custom...

    I was thinking more on the like of a custom exhaust builder.I haven't a grinder but least i know where to take it now thanks.
  16. Replies
    7
    Views
    2,690

    SS exhaust pipe needs cutting

    I got a section of SS exhaust pipe that needs cutting is there anywhere local that can do this in the Melksham/Trowbridge /Bath area. need about 2.5 cm cut off.
  17. Thread: Valve shims

    by alanTDM
    Replies
    10
    Views
    3,553

    Been on website will need to ring them when i got...

    Been on website will need to ring them when i got the dimensions ,Are you still on Carpe TDM .net or no TDM now?
  18. Thread: Valve shims

    by alanTDM
    Replies
    10
    Views
    3,553

    Thanks for that info , i'll need to check the...

    Thanks for that info , i'll need to check the measurements for the bends etc first.
  19. Thread: Valve shims

    by alanTDM
    Replies
    10
    Views
    3,553

    At mo im busy trying to find someone who can bend...

    At mo im busy trying to find someone who can bend exhausts pipes to match my tail pipes/ Y link pipe to replace my collector box,but i'm sure you will manage ok :-)
  20. Thread: Valve shims

    by alanTDM
    Replies
    10
    Views
    3,553

    I have done mine twice since i had the Yamaha TDM...

    I have done mine twice since i had the Yamaha TDM since 2005 and they have to be done every 24K,I let a dealer do mine first of all but they charged £140 for just doing the valves.It dont take long...
  21. Thread: Valve shims

    by alanTDM
    Replies
    10
    Views
    3,553

    Wait till you checked them,you might only need a...

    Wait till you checked them,you might only need a few,not sure what bike you got but i would get OM (from Fowlers etc)not after market shims.You will need a Haynes or workshop manual to work out what...
  22. Chain & Sprockets - What works well and what dosent

    Link:- http://www.gearingcommander.com/
  23. Replies
    6
    Views
    3,033

    Called in GM Stevens today to get some sprockets...

    Called in GM Stevens today to get some sprockets asked about the online Loyalty discount.Apparently if you go on the website you can order the parts then click will collect then when you get the...
  24. Thread: Northwest 200

    by alanTDM
    Replies
    9
    Views
    2,968

    here is a link to Cookstown 2013...

    here is a link to Cookstown 2013 http://www.bbc.co.uk/iplayer/episode/b01sgphy/Bikes!_2013_Cookstown_100/
  25. Replies
    6
    Views
    3,033

    Thanks Rabb be good if they did a discount card...

    Thanks Rabb be good if they did a discount card for peeps who go over there and not get anything online,myself might not go to the shop for quite a few months then find that im going there 3-4times...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4